Researchers Explore Voltage-Driven Liquid Metal Fractals

Researchers from North Carolina State University have found that gallium indium (EGaIn), a liquid metal with one of the highest surface tensions, can be induced to spread and form patterns called fractals with the application of low voltage. The work has implications for controlling the shape of liquid metals.

Surface tension is the force exerted by the surface of a liquid that causes it to “bead up” or form droplets. Water, for example, has a high surface tension, so it beads up, whereas alcohol, with a lower surface tension, tends to spread out. Liquid metals, such as mercury, have enormous surface tension and thus are almost always spherical. In fact, EGaIn has the highest surface tension of any known liquid at room temperature.

In a surprising finding, NC State professor of physics Karen Daniels and professor of chemical and biomolecular engineering Michael Dickey discovered that applying low voltage to the surface of EGaIn causes the liquid metal to spread out and form snowflake-like fractal patterns.

“Applying voltage to EGaIn forms a thin layer of oxide on the surface of the metal, which effectively lowers the surface tension,” Dickey says. “Normally, the tension of liquids can be lowered by adding surfactants – like putting soap or detergent in water – to the liquid. It’s easy to put soap into water, but hard to get the soap out. In contrast, the use of voltage to control the tension is interesting because it is reversible, and incredibly effective.”

“We also found that if you apply higher amounts of voltage to the metal it stops spreading and beads up again,” Daniels says. “That’s due to the amount of oxide produced – a small amount lowers the surface tension, but too much forms a crust over the metal and stops it spreading. So controlling the voltage is a nice way to control the spreading of the metal.”

The researchers recorded the metal’s behavior as the surface tension lowered. Less than one volt of electricity caused the metal to spread out and form different fractals, or patterns. Interestingly, the fractals formed by the EGaIn appear to be unique; that is, they do not match any currently described fractals. “Aside from being unusual, the other implication of these fractals is that in order for them to form the surface tension of the liquid metal must be close to zero,” Daniels says.

“This work suggests that not only does the formation of the oxide lower the surface tension of the liquid metal, but that it also creates compressive stresses – the opposite of tension – that help the metal spread out and form fractals,” Dickey says. “This is interesting because liquids are always under tension, and we now have a tool to apply compressive forces directly to the surface of a liquid. These properties give us greater control over the metal’s behavior.”

The work appears in Physical Review Letters, and is funded by the National Science Foundation (grants DMR-1608097 and CMMI-0954321) and the Air Force Research Lab. Daniels is corresponding author. Graduate student Collin Eaker and undergraduate students David Hight and John O’Reagan contributed to the work.

-peake-

Note to editors: An abstract of the paper follows.

“Oxidation-Mediated Fingering in Liquid Metals”

DOI: 10.1103/PhysRevLett.119.174502

Authors: Collin Eaker, David Hight, John O’Reagan, Michael Dickey and Karen Daniels, North Carolina State University
Published: Physical Review Letters

Abstract:
We identify and characterize a new class of fingering instabilities in liquid metals; these instabilities are unexpected due to the large interfacial tension of metals. Electrochemical oxidation lowers the effective interfacial tension of a gallium-based liquid metal alloy to values approaching zero, thereby inducing drastic shape changes, including the formation of fractals. The measured fractal dimension (D = 1:3_0:05) places the instability in a different universality class than other fingering instabilities. By characterizing changes in morphology and dynamics as a function of droplet volume and applied electric potential, we identify the three main forces involved in this process: interfacial tension, gravity, and oxidative stress. Importantly, we find that electrochemical oxidation can generate compressive interfacial forces that oppose the tensile forces at a liquid interface. Thus, the surface oxide layer not only induces instabilities, but ultimately provides a physical and electrochemical barrier that halts the instabilities at larger positive potentials. Controlling the competition between interfacial tension and oxidative (compressive) stresses at the interface is important for the development of reconfigurable electronic, electromagnetic, and optical devices that take advantage of the metallic properties of liquid metals.

This post was originally published in NC State News.

Leave a Response

Your email address will not be published. All fields are required.